Electrochemical immunosensing of low-density lipoprotein based on sol-gel encapsulation

Abstract Lipoprotein monitoring is desirable in the management of medical conditions such as atherosclerotic cardiovascular disease and coronary artery disease, in which controlling the concentration of these chylomicrons is crucial. Current clinical methods are complex and present poor reproducibility between laboratories. For these reasons, recent guidelines discard the assessment of low-density lipoprotein cholesterol (LDL-C) as a routine analysis during lipid-lowering therapies. Concerning the importance of monitoring this parameter, the authors present an electrochemical immunosensor constructed from a simple and easy-to-reproduce platform that allows detecting and quantifying LDL nanoparticles directly from human serum samples. The performance of the biosensor was studied by scanning electron microscopy, cyclic voltammetry, and electrochemical impedance spectroscopy. The biosensing platform displays good stability and linearity between 30 mg dL-1 and 135 mg dL-1 with a detection limit of 20 mg dL-1. The proposed biosensor can be easily employed for monitoring LDL concentration in clinical treatments.

Influence of the composition and shades of ceramics on light transmission and degree of conversion of dual-cured resin cements

Abstract Objective Since the transmittance of ceramics can influence the degree of conversion (DC) of resin cements, ceramics composition and shade should be considered in the selection of resin cement. This in vitro study aimed to evaluate the effect of the transmittance of different composition, opacities and shades of ceramics on the degree of conversion of two dual-cured resin cements. Methodology Sixty discs were prepared from low translucency (LT) and medium opacity (MO) lithium disilicate ceramic, and zirconia ceramic (Z). Each group was subdivided into 5 subgroups (n=4) in shades A2, A3.5, B2, C2 and D3. The transmittance measurement was performed in a spectrophotometer. The Variolink II and Rely X U200 resin cements were photoactivated by LED (1400 mW/cm2) for 40 s through the ceramic discs and without the discs (control group). The DC was measured with infrared FTIR spectroscopy, immediately after light activation. Data were analyzed with Kruskall-Wallis and one-way ANOVA, following post-hoc comparisons by Tukey test and Pearson's correlation test (P<0.05). Results LT ceramic exhibited higher transmittance values compared to MO and Z ceramics. LTA2 and LTB2 showed statistically higher transmittance values compared to MOA2, MOA3.5 and ZA3.5. For Variolink II, the ceramic interposition did not influence the DC, since there were no statistical differences between groups with ceramic interposition and the control group. For Rely X U200 cement, the interposition of some ceramics types/shades (LTA3.5, MOA2, MOA3.5 and ZA3.5) significantly decreased the DC values compared to control group. A positive correlation was found between the ceramic transmittance and DC values of both tested cements. Conclusions. The transmittance and DC values of the cements were influenced by composition and shades of the ceramics. The higher the transmittance of ceramics, the higher the DC values for both cements.

Effect of radiant exposure and UV accelerated aging on physico-chemical and mechanical properties of composite resins

Abstract Currently, there is no consensus in terms of defining the minimum radiant exposure values necessary for achieving adequate properties of composite resin. In addition, the long-term influence that radiant exposure has on the properties of composite resins is still questionable. Objective: The objective of this study was to evaluate the effect of radiant exposure and UV accelerated aging on the physico-chemical and mechanical properties of micro-hybrid and nanofilled composite resins. Material and Methods: A nanofilled (Filtek Supreme; 3M ESPE) and a micro-hybrid composite resin (Filtek Z250; 3M ESPE) were investigated under different radiant exposures (3.75, 9, and 24 J/cm2) and UV accelerated aging protocols (0, 500, 1000, and 1500 aging hours). The degree of conversion (DC), flexural strength (FS), modulus (M), water sorption (WS), and solubility (WL) were evaluated. The results obtained were analyzed using two-way ANOVA and Tukey's test. Comparisons were performed using a significance level of α=0.05. Results: The DC, FS, and M were found to be significantly influenced by both radiant exposure and accelerated aging time. The DC and EM increased with radiant exposure in the no-aging group (0-hour aging) for both micro-hybrid and nanofilled composites, whereas no correlation was found after accelerated aging protocols. WS and WL of micro-hybrid and nanofilled composite resins were scarcely affected by radiant exposure (p>0.05), whereas they were significantly reduced by accelerated aging (p<0.001). Conclusions: Although increasing radiant exposure affected the degree of conversion and mechanical properties of micro-hybrid and nanofilled composites, no influence on the hydrolytic degradation of the material was observed. In contrast, UV accelerated aging affected both the physico-chemical and mechanical properties of the composites.

In Situ Cross-Linkable Hydrogels as a Dynamic Matrix for Tissue Regenerative Medicine

BACKGROUND: Polymeric hydrogels are extensively used as promising biomaterials in a broad range of biomedical applications, including tissue engineering, regenerative medicine, and drug delivery. These materials have advantages such as structural similarity to the native extracellular matrix (ECM), multi-tunable physicochemical and biological properties, and biocompatibility. METHODS: In situ forming hydrogels show a phase transition from a solution to a gel state through various physical and chemical cross-linking reactions. These advanced hydrogel materials have been widely used for tissue regenerative medicine because of the ease of encapsulating therapeutic agents, such as cells, drugs, proteins, and genes. RESULTS: With advances in biomaterials engineering, these hydrogel materials have been utilized as either artificial cellular microenvironments to create engineered tissue constructs or as bioactive acellular matrices to stimulate the native ECM for enhanced tissue regeneration and restoration. CONCLUSION: In this review, we discuss the use of in situ cross-linkable hydrogels in tissue engineering and regenerative medicine applications. In particular, we focus on emerging technologies as a powerful therapeutic tool for tissue regenerative medicine applications.

Thermoresponsive and Biodegradable Amphiphilic Block Copolymers with Pendant Functional Groups

BACKGROUND: To develop the biodegradability and thermoresponsive hydrogel, in this work we designed a pendant-functionalized, thermoresponsive, amphiphilic block copolymer. METHODS: Methoxy poly(ethylene glycol) (MPEG)-b-[poly(ε-caprolactone)-ran-poly(ε-caprolactone-3-one)-ran-polylactic acid] (MCL) and (MPEG-b-[PCL-ran-POD-ran-PLA]) [MCL-(CO)] block copolymers were prepared by ringopening polymerization of ε-caprolactone, OD and lactide monomers. The subsequent derivatization of MCL-(CO) provided MPEG-b-[PCL-ran-poly(ε-caprolactone-3-COOH)-ran-PLA] [MCL-(COOH)] with COOH pendant groups and MPEG-b-[PCL-ran-poly(ε-caprolactone-3-NH2)-ran-PLA] [MCL-(NH2)] with NH2 pendant groups. RESULTS: The measured segment ratios of MCL-(CO), MCL-(COOH), and MCL-(NH2) agreed well with the target ratios. The abundances of the COOH and NH2 groups in the MCL-(COOH) and MCL-(NH2) copolymers were determined by 1H- and 13C-nuclear magnetic resonance spectroscopy, and agreed well with the target abundances. MCL-(CO), MCL-(COOH), and MCL-(NH2) formed homogeneous, white, opaque emulsions at room temperature. Rheological analysis of the block copolymer suspensions indicated a solution-to-hydrogel phase transition as a function of temperature. The solution-to-hydrogel phase transitions and the biodegradation of MCL-(CO), MCL-(COOH), and MCL-(NH2) were affected by varying the type (ketone, COOH, or NH2) and abundance of the pendant groups. CONCLUSION: MCL-(CO), MCL-(COOH), and MCL-(NH2) with ketone, COOH, and NH2 pendant groups showed solution-to-hydrogel phase transitions and biodegradation behaviors that depended on both the type and number of pendant groups.

Evaluation of long-term bond strength and selected properties of self-adhesive resin cements

Abstract This study evaluated the shear bond strength (SBS) of self-adhesive resin cements (SARCs) to dentin and their physical-chemical properties. Five commercial SARCs were evaluated [SmartCem®2 - DENTSPLY (SC2); BisCem® - Bisco (BC); SeT PP® − SDI (SeT); Relyx U100® - 3M ESPE (U100) and YCEM® SA - Yller (YCEM)]. The SARCs were evaluated for SBS to dentin (n = 10) after 24 h, 6 months, and 12 months. The dentin demineralization caused by acidic monomers was observed by SEM, and pH-neutralization of eluate was observed for 24 h. Degree of conversion (DC), rate of polymerization (Rp), flexural strength (FS), and elastic modulus (E) were evaluated. Immediate SBS of SC2, SET, U100, and YCEM were statistically higher than that of BC (p < 0.001). After 12 months, all SARCs showed reduced SBS values and U100 showed values similar to those of SET and YCEM, and higher than those of BC and SC2 (p = 0.001). Demineralization pattern of SARCs was similar. At 24h, all SARCs showed no differences in the pH-value, except BC and U100 (p < 0.001). YCEM showed the highest Rp. U100, YCEM, and SC2 showed statistically higher FS (p<0.001) and E (p < 0.001) when compared with SET and BC. U100 and YCEM showed the best long-term bonding irrespective of the storage period. A significant reduction in SBS was found for all groups after 12 months. SBS was not shown to be correlated with physical-chemical properties, and appeared to be material-dependent. The polymerization profile suggested that an increased time of light activation, longer than that recommended by manufacturers, would be necessary to optimize DC of SARCs.

A comparative study of bulk-fill composites: degree of conversion, post-gel shrinkage and cytotoxicity

Abstract: Bulk-fill composites are claimed to be restorative materials used in deep preparations and effectively photoactivated in layers up to 4 mm. The aim of the present study was to evaluate the degree of conversion, post-gel volumetric shrinkage, and cytotoxicity of six bulk-fill and two conventional composites. Degree of conversion was determined by FTIR spectroscopy; post-gel volumetric shrinkage was determined using the strain gauge method; and cytotoxicity in human fibroblasts was evaluated indirectly by the MTT assay. Data were subjected to one-way ANOVA/Tukey's test (α = 0.05). All materials, including bulk-fill and conventional composites, were classified as non-toxic, with cell viability higher than 70%. Bulk-fill composites exhibited volumetric shrinkage similar to or lower (1.4 to 0.4%) than that of conventional composites (1.7-2.1%). However, only four of the bulk-fill composites were able to sustain a homogeneous conversion at the 4-mm depth. Despite their non-toxicity and shrinkage similar to that of conventional materials, not all commercial bulk-fill materials were able to maintain a conversion as high as 80% of the superficial layer, at the 4-mm depth, indicating some failure in the bulk-fill design of some commercial brands. Therefore, the use of bulk-fill materials in dental practice is advantageous, but special attention should be given to the selection and correct use of the materials.

Effect of different bonding protocols on degree of monomer conversion and bond strength between orthodontic brackets and enamel

Abstract The objective of the present study was to evaluate the effect of different surface treatments and polymerization protocols on the bond strength of brackets to enamel, and the degree of conversion of the bonding agents. 120 bovine crowns were embedded in acrylic resin blocks and sanded. Next, the blocks were randomly assigned into 12 groups. Metal brackets were bonded to enamel according to the "surface treatment" factor (A: Phosphoric Acid; ATxt: Phosphoric Acid + Transbond XT Primer®; Tse: Transbond Plus Self Etching Primer®; and SBU: Scotchbond Universal®) and "polymerization" factor (R20: Radii-Cal®/20 seconds; V20: Valo Cordless®/20 seconds; and V3: Valo Cordless®/3 seconds). All samples were stored for 6 months (water, 37ºC) and then subjected to a shear bond strength test (SBS). Bond failures were classified according to the Adhesive Remnant Index (ARI) and analyzed with the Kruskal-Wallis and Mann-Whitney tests (5%). Using the same factors, 120 resin discs were made to assess the degree of conversion (DC) of the monomer. Data from the SBS (MPa) and DC (%) were analyzed by analysis of variance (2 factors) and Tukey's test (5%). For the SBS, the factors "polymerization" (R20 = 8.1B; V20 = 13.2A; V3 = 5.2C, p = 0.0001) and "surface treatment" (A = 3.1C; ATxt = 13.6A; Tse = 12.3A; SBU = 6.3B, p = 0.0001) were statistically significant among groups. The highest adhesion value were found for the ATxt/V20 group (22.2A) and the lowest value for the A/R20 group (1.2E). Regarding ARI, score 2 was the most prevalent in groups A, ATxt, V20 and V3, while score 4 was the most prevalent in the Tse, SBU and R20 groups, with no significant difference between them (p = 1.0). Regarding DC, the factors "polymerization" (R20 = 66.6A; V20 = 58.4B; V3 = 45.1C, p = 0.0001) and "surface treatment" (A = 52B, ATxt = 59.7A, Tse = 51.4B, SBU = 63.8A, p = 0.0001) were statistically significant. Tse was more sensitive to the variations in polymerization protocols than the other surface treatments. Treatment A did not present suitable bond strength or degree of conversion.

Influence of a hydrophobic monomer on the physical and mechanical properties of experimental surface sealants

Abstract This study evaluated the effect of adding the hydrophobic monomer 1,12 dodecanediol dimethacrylate (DDDMA) to experimental sealants with and without thermocycling on degree of conversion (DC), water sorption (WS), water solubility (WSB), color stability (ΔE), and micro-shear bond strength (μSBS). Five experimental and one commercially available sealant (Bisco - BIS) were tested. The experimental sealants were formulated by mixing different percentages of DDDMA monomers and urethane dimethacrylate (UDMA). The photoinitiator system was composed by camphorquinone (CQ) and tertiary amine 4-ethyl benzoate dimetilamiono (EDBA). Ethanol was used as a solvent. The experimental groups were named sequentially according to the monomeric content (DDDMA/UDMA): S40/40 (40/40), S50/30 (50/30), S60/20 (60/20), S70/10 (70/10) and S80/0 (80/0). Data were analyzed separately by one-way ANOVA, followed by Tukey's test (p<0.05). The values of DC ranged from 94.59% (S40/40) to 54.02% (S80/10). BIS showed the highest WS value (p<0.05) and S40/40, S50/30, S60/20 and S80/0 showed the lowest WS values of all tested sealants. WSB values ranged from 7.88 µg/mm3 (BIS) to 13.27 µg/mm3 (S70/10). The highest ΔE value was 11.05±2.88 for BIS and the highest μSBS value was found for S60/20. No significant difference was observed in bond strength between sealants and bovine enamel after thermocycling. Adding DDDMA to the composition of surface sealants can improve its performance, once the monomer increased the degree of conversion and the color stability.

Minimization of polymerization shrinkage effects on composite resins by the control of irradiance during the photoactivation process

Abstract High levels of shrinkage stress caused by volumetric variations during the activation process are one of the main problems in the practical application of composite resins. Objective The aim of this study is to reduce the shrinkage stress and minimize the effects caused by composite resin volumetric variation due to the photopolymerization. In this way, this work proposes a systematic study to determine the optimal dimming function to be applied to light curing processes. Material and Methods The study was performed by applying mathematical techniques to the optimization of nonlinear objective functions. The effectiveness of the dimming function was evaluated by monitoring the polymerization shrinkage stress during the curing process of five brands/models of composites. This monitoring was performed on a universal testing machine using two steel bases coupled in the arms of the machine where the resin was inserted and polymerized. The quality of the composites cured by the proposed method was analyzed and compared with the conventional photoactivation method by experiments to determine their degree of conversion (DC). Absorbance measurements were performed using Fourier-transform infrared spectroscopy (FT-IR). A T-test was performed on DC results to compare the photoactivation techniques. We also used scanning electron microscopy (SEM) to analyze in-vitro the adhesion interface of the resin in human teeth. Results Our results showed that the use of the optimal dimming function, named as exponential, resulted in the significant reduction of the shrinkage stress (~36.88% ±6.56 when compared with the conventional method) without affecting the DC (t=0.86, p-value=0.44). The SEM analyses show that the proposed process can minimize or even eliminate adhesion failures between the tooth and the resin in dental restorations. Conclusion The results from this study can promote the improvement of the composite resin light curing process by the minimization of polymerization shrinkage effects, given an operational standardization of the photoactivation process.

Effect on adhesion of a nanocapsules-loaded adhesive system

Abstract This study aimed to evaluate the in situ degree of conversion, contact angle, and immediate and long-term bond strengths of a commercial primer and an experimental adhesive containing indomethacin- and triclosan-loaded nanocapsules (NCs). The indomethacin- and triclosan-loaded NCs, which promote anti-inflammatory and antibacterial effects through controlled release, were incorporated into the primer at a concentration of 2% and in the adhesive at concentrations of 1, 2, 5, and 10%. The in situ degree of conversion (DC, n=3) was evaluated by micro-Raman spectroscopy. The contact angle of the primer and adhesive on the dentin surface (n = 3) was determined by an optical tensiometer. For the microtensile bond strength µTBS test (12 teeth per group), stick-shaped specimens were tested under tensile stress immediately after preparation and after storage in water for 1 year. The data were analyzed using two-way ANOVA, three-way ANOVA and Tukey's post hoc tests with α=0.05. The use of the NC-loaded adhesive resulted in a higher in situ degree of conversion. The DC values varied from 75.07 ± 8.83% to 96.18 ± 0.87%. The use of NCs in only the adhesive up to a concentration of 5% had no influence on the bond strength. The contact angle of the primer remained the same with and without NCs. The use of both the primer and adhesive with NCs (for all concentrations) resulted in a higher contact angle of the adhesive. The longitudinal μTBS was inversely proportional to the concentration of NCs in the adhesive system, exhibiting decreasing values for the groups with primer containing NCs and adhesives with increasing concentrations of NCs. Adhesives containing up to 5% of nanocapsules and primer with no NCs maintained the in situ degree of conversion, contact angle, and immediate and long-term bond strengths. Therefore, the NC-loaded adhesive can be an alternative method for combining the bond performance and therapeutic effects. The use of an adhesive with up to 5% nanocapsules containing indomethacin and triclosan and a primer with no nanocapsules maintained the long-term bond performance.

Crystal Modification on Lithium Disilicate Glass Ceramics Sintered Using Microwaves / Modificación de Cristales de Cerémicas de Vidrio de Disilicato de Litio Sinterizadas con Microondas

ABSTRACT: Microwaves are an interesting alternative to process dental ceramics. It is well documented that Microwave Hybrid Sintering (MHS) allows important savings in time and energy consumption. However, little is known about its effect on lithium disilicate glass ceramics, a popular material in dentistry today. We analyzed the microstructure of lithium disilicate glass ceramics sintered with MHS compared with conventional sintering. We sintered lithium disilicate glass ceramics using MHS and conventional furnaces, and we analyzed the samples using X-Ray diffraction and SEM. Samples sintered with MHS showed an increased crystalline phase, with an increased number of crystals. These crystals have larger perimeters compared with samples sintered in conventional furnaces. MHS produced a different crystallization pattern and crystal/ matrix ration in lithium disilicate glass ceramics when compared to conventional sintering. This can be associated with the improved mechanical properties of these materials reported previously.

RESUMEN: Las microondas son una interesante alternativa para procesar cerámicas dentales. Está bien documentado que el Sinterizado Híbrido por Microondas (MHS) permite ahorros importantes de tiempo y energía. Sin embargo, poco se ha publicado respecto a sus efectos en cerámicas de disilicato de litio, un material bastante popular en odontología en estos días. En este artículo analizamos la micro estructura de cerámicas de disilicato de litio sinterizada con MHS comparada con el sinterizado convencional. Sinterizamos muestras de cerámicas de disilicato de litio usando MHS y hornos convencionales, y analizamos las muestras usando difracción de rayos X y SEM. Las muestras sintetizadas usando MHS tienen una mayor fase cristalina, con mayor número de cristales. Estos cristales tienen además perímetros mayores, comparados con las muestras sinterizadas en hornos convencionales. MHS produce patrones de cristalización y proporción de cristal/matrix diferentes a las producidos por sinterizado convencional. Esto puede asociarse a las mejoras en propiedades mecánicas reportadas previamente.

Mulheres atletas olímpicas brasileiras: início e final de carreira por modalidade esportiva / Brazilian olympic athletes women: initial and final career by sports modality

Este estudo buscou investigar o contexto e a idade de início e final de carreira das mulheres atletas olímpicas brasileiras, bem como a razão do encerramento da carreira. Para tanto, participaram da amostra 444 mulheres brasileiras participantes de Jogos Olímpicos até Londres em 2012. Dos relatos de vida, foram retirados dados relacionados aos objetivos deste estudo. Os resultados nos permitem inferir que, em modalidades como natação, ginástica e tênis, o início foi muito precoce, já nos esportes coletivos a idade de início corresponde à fase escolar, quando neste momento o profissional de Educação Física é o principal responsável pela iniciação ao rendimento. Esportes como tiro, arco, boxe e levantamento de peso têm seu início já no final da adolescência. Com relação ao final de carreira, a faixa etária de aposentadoria corresponde à modalidade, e naqueles esportes em que se começa cedo, as idades de aposentadoria são menores. Observou-se também que os motivos principais para a finalização da carreira são: número de lesões, fadiga e cansaço, percepção de que a idade estava atrapalhando, maternidade e casamento e a necessidade de continuar os estudos. Outro fato abordado foi a exclusão da atleta pela comissão técnica, o que foi determinante para que a atleta não quisesse mais fazer parte daquele meio. A escolha de uma nova profissão e outro fator importante e que nos apresenta um panorama diferenciado para as atletas olímpicas, já que 50% destas se formaram e hoje, a grande maioria (65%) trabalham na área esportiva. Pode-se concluir que cada modalidade tem o momento ideal de início e que as atletas olímpicas não saíram deste padrão. Quanto ao término da carreira, este pode não ser compulsório (lesões, cansaço e fadiga, dispensas da equipe, maternidade, casamento) ou programado (formação acadêmica e profissional, necessidade de novas metas)....(AU)

The purpose of this study was to investigate the context of Brazilian women athletes, specifically the age at which they began and ended their careers, the reason for ending their careers and surrounding factors. For that, the sample was attended by 444 Brazilian women participating in the Olympic Games until London in 2012. Data related to the objectives of this study were collected from self-reports from the athletes. The results showed that in modalities such as swimming, gymnastics and tennis, the starting age for athletes was very young. In collective sports, the starting age corresponded to the age of schooling, wherein Physical Education is responsible for the initiation to the sport. Sports such as shooting, archery, boxing and weight lifting have their beginning as early as the end of adolescence. The age of retirement was found to correspond with the modality, whereby those sports that are begun at an early age were found to be associated with earlier retirement ages. It was also noted that the main reasons for career completion are: multiple injuries, fatigue, distress caused by self-perception of old age, maternity and marriage, and the continuation of studies. Another factor addressed was the exclusion of an athlete by a technical committee, acting as a driving force for the athlete to no longer want to be part of the sport environment. Following departure from a sport, the choice of a new profession is another important factor that presents us with a view of the Olympic athletes, since 50% of retired athletes went on to complete undergraduate degrees and the vast majority (605) went on to work in sport. It can be concluded that each modality has an ideal age at which to begin the sport and the Olympic athletes adhered to this standard. As for the end of the careers, the age of completion cannot be programmed in some cases (e.g. due to injuries, fatigue, team layoffs, maternity, marriage) and can be programmed in other cases (academic and professional training, need for new goals)....(AU)

Does laser diode irradiation improve the degree of conversion of simplified dentin bonding systems?

Abstract Simplified dentin-bonding systems are clinically employed for most adhesive procedures, and they are prone to hydrolytic degradation. Objective This study aimed to investigate the effect of laser diode irradiation on the degree of conversion (DC), water sorption (WS), and water solubility (WSB) of these bonding systems in an attempt to improve their physico-mechanical resistance. Material and Methods Two bonding agents were tested: a two-step total-etch system [Adper™ Single Bond 2, 3M ESPE (SB)] and a universal system [Adper™ Single Bond Universal, 3M ESPE (SU)]. Square-shaped specimens were prepared and assigned into 4 groups (n=5): SB and SU (control groups - no laser irradiation) and SB-L and SU-L [SB and SU laser (L) - irradiated groups]. DC was assessed using Fourier transform infrared spectroscopy with attenuated total reflectance. Additional uncured resin samples (≈3.0 µL, n=5) of each adhesive were also scanned for final DC calculation. For WS/WSB tests, similar specimens (n=10) were prepared and measured by monitoring the mass changes after dehydration/water storage cycles. For both tests, adhesive fluids were dropped into standardized Teflon molds (6.0×6.0×1.0 mm), irradiated with a 970-nm laser diode, and then polymerized with an LED-curing unit (1 W/cm2). Results Laser irradiation immediately before photopolymerization increased the DC (%) of the tested adhesives: SB-L>SB>SU-L>SU. For WS/WSB (μg/mm3), only the dentin bonding system (DBS) was a significant factor (p<0.05): SB>SU. Conclusion Irradiation with a laser diode improved the degree of conversion of all tested simplified dentin bonding systems, with no impact on water sorption and solubility.

Effects of radiant exposure values using second and third generation light curing units on the degree of conversion of a lucirin-based resin composite

Abstract Alternative photoinitiators with different absorption wavelengths have been used in resin composites (RCs), so it is crucial to evaluate the effectiveness of light-curing units (LCUs) on these products. Objective Using Fourier transform infrared analysis (FTIR) in vitro, the effects of varying radiant exposure (RE) values generated by second and third generation LED LCUs on the degree of conversion (DC) and maximum rate of polymerization (Rpmax) of an experimental Lucirin TPO-based RC were evaluated. Material and Methods 1 mm or 2 mm thick silicon molds were positioned on a horizontal attenuated total reflectance (ATR) unit attached to an infrared spectroscope. The RC was inserted into the molds and exposed to varying REs (18, 36 and 56 J/cm2) using second (Radii Plus, SDI) and third generation LED LCUs (Bluephase G2/Ivoclar Vivadent) or a quartz tungsten based LCU (Optilux 501/SDS Kerr). FTIR spectra (n=7) were recorded for 10 min (1 spectrum/s, 16 scans/spectrum, resolution 4 cm-1) immediately after their application to the ATR. The DC was calculated using standard techniques for observing changes in aliphatic to aromatic peak ratios both prior to, and 10 min after curing, as well as during each 1 second interval. DC and Rpmax data were analyzed using 3-way ANOVA and Tukey’s post-hoc test (p=0.05). Results No significant difference in DC or Rpmax was observed between the 1 mm or 2 mm thick specimens when RE values were delivered by Optilux 501 or when the 1 mm thick composites were exposed to light emitted by Bluephase G2, which in turn promoted a lower DC when 18 J/cm2 (13 s) were delivered to the 2 mm thick specimens. Radii Plus promoted DC and Rpmax values close to zero under most conditions, while the delivery of 56 J/cm2 (40 s) resulted in low DC values. Conclusions The third generation LCU provided an optimal polymerization of Lucirin TPO-based RC under most tested conditions, whereas the second generation LED-curing unit was useless regardless of the RE.

Influence of addition of [2-(methacryloyloxy)ethyl]trimethylammonium chloride to an experimental adhesive

Abstract The aim of this study was to develop an experimental adhesive with addition of [2-(methacryloyloxy)ethyl]trimethylammonium chloride (METAC) and to evaluate its mechanical and biological properties and its in vitro antibacterial activity. An experimental adhesive resin was formulated with Bis-GMA, TEGDMA, and HEMA. The antibacterial monomer was added at concentrations of 1%, 2.5%, and 5% (METAC groups). A group without METAC addition was used as control. The experimental adhesives were evaluated as to their antibacterial potential against Streptococcus mutans, degree of conversion, and softening in ethanol for 2 hours. The data were analyzed by one-way ANOVA, Tukey’s post-hoc test, and the paired Student’s t-test (significance level of 0.05). METAC showed antibacterial activity against S. mutans at all concentrations (p < 0.05). There was no statistical difference across METAC groups (p > 0.05). The 1%, 2.5%, and 5% groups yielded the highest mean values for degree of conversion (p < 0.05). The 1% group did not differ from the control group (p > 0.05). There was no statistical difference in baseline microhardness values (p > 0.05) and microhardness values after immersion in ethanol were lower than at baseline for all groups (p < 0.05). There was no statistical difference in the reduction of Knoop hardness number (KHN) after immersion in ethanol for any of the groups (p > 0.05). The results of the present study indicate that METAC is a promising antibacterial agent when added to an adhesive system.

Poloxamer 407 Hydrogels for Intravesical Instillation to Mouse Bladder: Gel-Forming Capacity and Retention Performance

PURPOSE: Poloxamer 407 (P407) thermo-sensitive hydrogel formulations were developed to enhance the retention time in the urinary bladder after intravesical instillation. MATERIALS AND METHODS: P407 hydrogels (P407Gels) containing 0.2 w/w% fluorescein isothiocyanate dextran (FD, MW 4 kDa) as a fluorescent probe were prepared by the cold method with different concentrations of the polymer (20, 25, and 30 w/w%). The gel-forming capacities were characterized in terms of gelation temperature (G-Temp), gelation time (G-Time), and gel duration (G-Dur). Homogenous dispersion of the probe throughout the hydrogel was observed by using fluorescence microscopy. The in vitro bladder simulation model was established to evaluate the retention and drug release properties. P407Gels in the solution state were administered to nude mice via urinary instillation, and the in vivo retention behavior of P407Gels was visualized by using an in vivo imaging system (IVIS). RESULTS: P407Gels showed a thermo-reversible phase transition at 4℃ (refrigerated; sol) and 37℃ (body temperature; gel). The G-Temp, G-Time, and G-Dur of FD-free P407Gels were approximately 10℃–20℃, 12–30 seconds, and 12–35 hours, respectively, and were not altered by the addition of FD. Fluorescence imaging showed that FD was spread homogenously in the gelled P407 solution. In a bladder simulation model, even after repeated periodic filling-emptying cycles, the hydrogel formulation displayed excellent retention with continuous release of the probe over 8 hours. The FD release from P407Gels and the erosion of the gel, both of which followed zero-order kinetics, had a linear relationship (r²=0.988). IVIS demonstrated that the intravesical retention time of P407Gels was over 4 hours, which was longer than that of the FD solution ( < 1 hour), even though periodic urination occurred in the mice. CONCLUSIONS: FD release from P407Gels was erosion-controlled. P407Gels represent a promising system to enhance intravesical retention with extended drug delivery.

Silver nanoparticle incorporation effect on mechanical and thermal properties of denture base acrylic resins

ABSTRACT Objective The aim of the present study was to evaluate the mechanical and thermal characteristics of two denture base acrylic resins containing silver nanoparticles (AgNPs). Material and Methods Two different acrylic denture base resins (heat-polymerized and microwave polymerized) containing 0.3, 0.8 and 1.6 wt% AgNPs were evaluated for flexural strength, elastic modulus and impact strength. The glass transition temperature (Tg) and relative heat capacity (Cp) of the samples were determined from the Differential Scanning Calorimetry (DSC) results. For statistical analysis, two-way ANOVA and Tukey-HSD tests were performed. Results Addition of 0.8% and 1.6% AgNPs in microwave-polymerized resin significantly decreased the transverse strength and elastic modulus. In terms of impact strength, the addition of AgNPs has no effect on both resin groups. Glass transition temperature (Tg) was decreased with the addition of AgNPs for both denture base resins. Conclusions The incorporation of AgNPs, generally used for antimicrobial efficiency, affected the transverse strength of the denture base acrylic resins depending on the concentration of nanoparticles. Tg was decreased with the addition of AgNPs for both denture base resins.

Evaluation of phenyl-propanedione on yellowing and chemical-mechanical properties of experimental dental resin-based materials

ABSTRACT Objective To evaluate the influence of phenyl-propanedione on yellowing and chemical-mechanical properties of experimental resin-based materials photoactivated using different light curing units (LCUs). Material and Methods Experimental resin-based materials with the same organic matrix (60:40 wt% BisGMA:TEGDMA) were mechanically blended using a centrifugal mixing device. To this blend, different photoinitiator systems were added in equimolar concentrations with aliphatic amine doubled by wt%: 0.4 wt% CQ; 0.38 wt% PPD; or 0.2 wt% CQ and 0.19 wt% PPD. The degree of conversion (DC), flexural strength (FS), Young’s modulus (YM), Knoop hardness (KNH), crosslinking density (CLD), and yellowing (Y) were evaluated (n=10). All samples were light cured with the following LCUs: a halogen lamp (XL 2500), a monowave LED (Radii), or a polywave LED (Valo) with 16 J/cm2. The results were analysed by two-way ANOVA and Tukey’s test (α=0.05). Results No statistical differences were found between the different photoinitiator systems to KNH, CLS, FS, and YM properties (p≥0.05). PPD/CQ association showed the higher DC values compared with CQ and PPD isolated systems when photoactivated by a polywave LED (p≤0.05). Y values were highest for the CQ compared with the PPD systems (p≤0.05). Conclusion PPD isolated system promoted similar chemical and mechanical properties and less yellowing compared with the CQ isolated system, regardless of the LCU used.

Influence of polymeric matrix on the physical and chemical properties of experimental composites

Nowadays, the main reasons for replacement of resin-based composite restorations are fracture or problems with the integrity of their interface, such as marginal staining, microleakage, or secondary caries. The aim of the present study was to evaluate the influence of the organic matrix on polymerization stress (PS), degree of conversion (DC), elastic modulus (E), flexural strength (FS), Knoop hardness (KHN), sorption (SP), and solubility (SL). In order to obtain a material which combines better mechanical properties with lower PS, seven experimental composites were prepared using BisGMA to TEGDMA molar ratios of 2:8, 3:7, 4:6, 5:5, 6:4, 7:3 and 8:2 and 40% of silica. PS was obtained in a universal testing machine, using acrylic as bonding substrate. DC was determined using Fourier Transform Raman spectroscopy. E and FS were obtained by the three-point bending test. KHN was measured by a microindentation test using a load of 25 g for 30 s. SP and SL were assessed according to ISO 4049. The data were submitted to one-way ANOVA. The increase in BisGMA concentration resulted in the decrease of PS, DC, E, FS and KHN. However, it did not change the SP and SL values. FS, E and KHN showed a strong and direct relationship with the DC of the materials. The composite material with a BisGMA to TEGDMA molar ratio of 1:1 was the one with better mechanical properties and lower PS.